Blueshockey6 0 Report post Posted December 27, 2009 I had a pair of Tour MX's blowout, skates were about 6months old, so I mailed them back to Tour for them to inspect (3rd pair of Tours to blow out in 2years), so in the mean time, I went out and bought a pair of the 2010 Mission Soldier SE's becuase I needed skates, love them... Get a call from Tour last Monday saying that they are going to replace my skates, however they don't have any MX's in the warehouse, all they have is a pair of Tour Beemers that they are going to send me, so I get the skates, put wheels on them today, on the one skate the 2nd wheel from the front is locked up, I pulled it up, bearing spins just fine off the skate, could there be an issue with the Beemers they sent me and the wheel rubbing the bottom of the boot? Share this post Link to post Share on other sites
diablo42 0 Report post Posted December 27, 2009 i think you've got an oversized wheel there. Share this post Link to post Share on other sites
Blueshockey6 0 Report post Posted December 27, 2009 i think you've got an oversized wheel there.That's not the case...They all roll fine on the other skate, 80mm's all around, so I tried several wheels, it's still locked, they mounted the chassis @ the warehouse from what they told me..Is it possible they mounted the chassis to far back on the bottom of the skate?? Share this post Link to post Share on other sites
tour17 0 Report post Posted January 3, 2010 Call Brad Brussatti, tell him Walter told you to contact him. He will make sure the problem is resolved.Brad Brussatti---217-324-3961 ext 121 Share this post Link to post Share on other sites
Ron 0 Report post Posted January 8, 2010 What size are you skates? To my surprise, when my older Tour Code E2's came in, they ran a straight 4 x 76mm wheel setup due to my smaller boot size 7. Apparently anything bigger than the 7 uses a 4 x 80mm setup. I believe th Beemers are around the same vintage as the original Code 1 and Code E2's. If you are trying to run 80's in a chassis designed for 76mm, you may get some interference Share this post Link to post Share on other sites
littlehockeymatt 0 Report post Posted January 9, 2010 To be honest, id just stick with the 2010 soldiers. My old skates are tour code 1's(the origanl) and 2months or so ago i got mission boss blacks and wow a huge difference. In my opinion mission makes better skates than tour. Durable, comterable!,good fit mission is the way to go Share this post Link to post Share on other sites
hockey_is_hard 0 Report post Posted January 23, 2010 I'm not sure about the Beemers, but i've had Tour Code Reds and Code Blues in the past. The 80mm wheels that come with the skates spun fine, but when i put Hyper 250 80mm wheels on them the second wheel won't spin (in both cases). It has to do with the width of the wheel rubbing against where the chassis is mounted next to the recessed area in the boot. Whenever I get new wheels I have to leave one of the original Labeda wheels in the second spot or a worn down Hyper there until the rest of the wheels wear down enough so that they won't rub when i rotate them. Share this post Link to post Share on other sites
Blueshockey6 0 Report post Posted January 26, 2010 Call Brad Brussatti, tell him Walter told you to contact him. He will make sure the problem is resolved.Brad Brussatti---217-324-3961 ext 121Brad is actually the one who sent me the skates, took them to my local hockey shop and they said that the chassis is mounted too far back on the boot Share this post Link to post Share on other sites
Chesterfield12 0 Report post Posted February 2, 2010 I am sorry, and not to call Brad out, but the only dealings I've had with the man have been untimely, and unprofessional. I would ask to speak with someone else at Tour if I were you. Share this post Link to post Share on other sites
Chad Seibel 2 Report post Posted March 26, 2010 Did this issue get resolved? Share this post Link to post Share on other sites
Blueshockey6 0 Report post Posted April 12, 2010 Did this issue get resolved?Sorry took so long to respond, been away..Anyways, no the issue with the Tour Beemers did not get resolved, they are still un-useableI dont know where to go from here, I guess they can be remounted?? Share this post Link to post Share on other sites
Chad Seibel 2 Report post Posted April 12, 2010 Sorry took so long to respond, been away..Anyways, no the issue with the Tour Beemers did not get resolved, they are still un-useableI dont know where to go from here, I guess they can be remounted??Give me message with your phone number and I will work with you on it. Lets get this settled up my friend. Share this post Link to post Share on other sites
Blueshockey6 0 Report post Posted April 14, 2010 Give me message with your phone number and I will work with you on it. Lets get this settled up my friend.Hey Chad just want to check to see if you got my info I pmed you? Share this post Link to post Share on other sites
flyweightphantom 1 Report post Posted April 14, 2010 Although I don't use tour this is great service by these guys, kudos! Share this post Link to post Share on other sites
Chad Seibel 2 Report post Posted April 15, 2010 I got it and will get back to you ASAP Share this post Link to post Share on other sites
