NikeBauer One90 Senior Composite Shaft

[flyrzman 0]

is this a tapered shaft?

[Rustpot 1]

no

[jigsaw 0]

hm.. so if i broke my one90 ops i can't cut it and put a tappered blade on it?

[D aka speck 0]

um... no

[chikinpotpie 138]

Actually you can.

If you cut right at the "P" in power profile a tapered blade will fit in it

Check out the show it off thread I have a picture of one

http://www.modsquadhockey.com/forums/index...mp;#entry524050

[habsfan87 0]

Actually you can.

If you cut right at the "P" in power profile a tapered blade will fit in it

Check out the show it off thread I have a picture of one

http://www.modsquadhockey.com/forums/index...mp;#entry524050

If you're referring to the one90/yellow blade, isn't that an easton ST blade? and aren't those standard?

[Rustpot 1]

It might be a CCM or a One50 blade.

Anyway, the shaft and OPS are two different animals. The shaft has a .620 taper, yes, but it's not long enough to effect the size of tenon required, only to slightly lower the kickpoint.

The OPS has the same taper, but it is longer. It isn't as thin as the Vapor line or other sticks, but it's still a tapered shaft.

Edit- A few posts later he said it was a CCM Vector 8.0 blade.

[Eternal 0]

It might be a CCM or a One50 blade.

Anyway, the shaft and OPS are two different animals. The shaft has a .620 taper, yes, but it's not long enough to effect the size of tenon required, only to slightly lower the kickpoint.

The OPS has the same taper, but it is longer. It isn't as thin as the Vapor line or other sticks, but it's still a tapered shaft.

Edit- A few posts later he said it was a CCM Vector 8.0 blade.

I could be completly wrong but i think the ops is an .520 taper not a .620.

[AnthonyJTa 0]

If you're referring to the one90/yellow blade, isn't that an easton ST blade? and aren't those standard?

He says 2 posts down that it's a CCM V8.0

[habsfan87 0]

If you're referring to the one90/yellow blade, isn't that an easton ST blade? and aren't those standard?

He says 2 posts down that it's a CCM V8.0

I see I see, I wasn't tryin to prove him wrong or anything, I just didn't know so I asked. It makes sense that the one-piece would be tapered and the shaft not, pretty much (give or take some things) a synergy to an ultralite all those years.

[Rustpot 1]

I could be completly wrong but i think the ops is an .520 taper not a .620.

Check the numbers.I went off memory, could be wrong.

[DCott 0]

vapor shaft is a .520. supreme is .620, or standard

[Rustpot 1]

Yeah, just checked.

One90 shaft - .620 standard

One90 OPS- .520 tapered

XXXX shaft- .520 tapered

XXXX OPS- .470 ultra-tapered!

[odp 0]

Awesome, my Bauer Endure uses the .470 ultra taper!

Come to think of it, I think my buddy's Bauer V uses it as well . . .

[burrn 0]

all vapor models(including previous/price point):

shaft 0.520

ops 0.470

[adam14 182]

vapor xxxx shaft? where you scoop that?

[Rustpot 1]

I was joking, .520 is tapered to fit a blade, .470 will be skinnier, have better performance, and make conversion from OPS to 2-piece difficult.

So it must be better?