romdj 26 Report post Posted April 10, 2013 (edited) has anyone who purchased makos had totalones in the past? I'd be interested in hearing the comparison and pros/cons that people have found Edited April 10, 2013 by romdj 1 Share this post Link to post Share on other sites
smcgreg 81 Report post Posted April 10, 2013 has anyone who purchased makos had totalones in the past? I'd be interested in hearing the comparison and pros/cons that people have foundYep. What do you want to know? You can read my first skate report further up the thread. Share this post Link to post Share on other sites
adam14 182 Report post Posted April 10, 2013 The only thing I'm not sold on is the tongue, is it replaceable? How thick is it? Share this post Link to post Share on other sites
flyers10 57 Report post Posted April 10, 2013 The only thing I'm not sold on is the tongue, is it replaceable? How thick is it?Not sure about the replacement aspect but it is a medium thickness with a plastic lace bite channel. Pretty comfortable to me and thicker than my x60's tongue. Share this post Link to post Share on other sites
trukweaz 3 Report post Posted April 10, 2013 Quick question on the fit-baking of these. I tried on a 7.5 and my toes are just feathering the toe cap. In a 7 I was pretty jammed in there (like uncomfortable). After hearing how much the heal sinks in on these should I go with the 7's or the 7.5's? Note, both tried on in thin easton hockey socks. Share this post Link to post Share on other sites
Buzz_LightBeer 984 Report post Posted April 10, 2013 I'd go 7.5, thinking you'd gain 1/4" or so with heating. Share this post Link to post Share on other sites
AfftonDad 88 Report post Posted April 10, 2013 (edited) The only thing I'm not sold on is the tongue, is it replaceable? How thick is it?They make a big deal out of how the tongue goes all the way down... It is apparently by design to eliminate negative space in the toe box. I'm not at home so I can't look at it but I suspect it isn't stiched in like a typical tongue and if you did want to stitch in a (different) replacement tongue you would probably lose the "feature" aspect of the "goes all the way down tongue". Edited April 10, 2013 by AfftonDad Share this post Link to post Share on other sites
trukweaz 3 Report post Posted April 10, 2013 I'd go 7.5, thinking you'd gain 1/4" or so with heating.Thanks, I was leaning that way. Share this post Link to post Share on other sites
JSK81 400 Report post Posted April 10, 2013 I gained a lot of lenght after baking. My toes were cramped unbaked, now they're just barely touching the cap. Share this post Link to post Share on other sites
mojo122 541 Report post Posted April 10, 2013 Tomorrow I'm putting LS2's on a pair for a MSH member. He's only changing them because he has $500 of lifetime Titanium steel in LS2. But I'm sure he'll post how they feel after he skates on them.Here’s a picture of what a Mako looks like with LS2 holders. Had I not already have 2 sets of titanium runners I would have given the CXN holder and steel a try, but I really like what I get out of my current steel. This particular runner has 2 years of sharpening on them at this point. Jimmy used the lifts off an old pair of skates I had, so I should still have close to the original Mako pitch had I left the CXN holders on. Jimmy can best answer how the process was in switching out the holders. Share this post Link to post Share on other sites
jimmy 194 Report post Posted April 10, 2013 Here’s a picture of what a Mako looks like with LS2 holders. Had I not already have 2 sets of titanium runners I would have given the CXN holder and steel a try, but I really like what I get out of my current steel. This particular runner has 2 years of sharpening on them at this point. Jimmy used the lifts off an old pair of skates I had, so I should still have close to the original Mako pitch had I left the CXN holders on. Jimmy can best answer how the process was in switching out the holders.haha, 2 yrs of sharpening and they still have all their height on them. You could probably pass those down from generation to generation. :-) Share this post Link to post Share on other sites
wrangler 157 Report post Posted April 10, 2013 Wont happen. Apparently I'm supposed to be 'promoted' to another role that would cut my pay by 20%I must admit that I'm really intrigued by this skate. Just went to the LHS, and their highest end skate was the lowest end Bauer supreme. "Mako, you mean the shark? Never heard of the skate?"Yeah, but you'll get a title, right? Share this post Link to post Share on other sites
DigiV 6 Report post Posted April 10, 2013 (edited) New member here, so hello. Few questions for those that have a pair or have tried one on. I'm totally sold on the skate but there's no LHS that carries them here. Was wondering what size to go with because i hear conflicting reports. Does the heel sink in? is it longer after baking? shorter after baking? I'm a 9.5 toe length foot but i usually wear 10 shoes. Some shoes like boat shoes are 9.5's, but most running shoes are 10's, dress shoes are usually 10s and my current x60's (bought used, molded to someone elses foot) are a tad too big at 8.5D. I'm wondering if i should go with an 8D in these. On the x60's my toes don't touch the toe box at all (maybe ever so so so slightly) but i wonder if that's because it's a used skate broken in with someone else's bigger foot. Edited April 10, 2013 by DigiV Share this post Link to post Share on other sites
althoma1 575 Report post Posted April 10, 2013 Quick question on the fit-baking of these. I tried on a 7.5 and my toes are just feathering the toe cap. In a 7 I was pretty jammed in there (like uncomfortable). After hearing how much the heal sinks in on these should I go with the 7's or the 7.5's? Note, both tried on in thin easton hockey socks.If you know you're going to buy for sure then just be honest with your LHS and tell them you're not sure if you need size 7 or 7.5 and won't be positive until after they're baked. Then ask if you can have the 7's baked and if they fit well buy them. If the 7s are still too small then go with the 7.5s. From other peoples posts it sounds like some shops are letting people bake these skates before making a final decision. Share this post Link to post Share on other sites
DEATHTRON 19 Report post Posted April 10, 2013 I will say that I feel like I gained 1/4 size with mine. Not sure I can fit into an 8, but the way it sits, the 8 1/2 leaves my toes not feathering the toe cap like normal. Then again, it could be the ergonomic toe cap, as my index toe is my longest.Zach Share this post Link to post Share on other sites
jazzyjoey 2 Report post Posted April 10, 2013 New member here, so hello. Few questions for those that have a pair or have tried one on. I'm totally sold on the skate but there's no LHS that carries them here. Was wondering what size to go with because i hear conflicting reports. Does the heel sink in? is it longer after baking? shorter after baking? I'm a 9.5 toe length foot but i usually wear 10 shoes. Some shoes like boat shoes are 9.5's, but most running shoes are 10's, dress shoes are usually 10s and my current x60's (bought used, molded to someone elses foot) are a tad too big at 8.5D. I'm wondering if i should go with an 8D in these. On the x60's my toes don't touch the toe box at all (maybe ever so so so slightly) but i wonder if that's because it's a used skate broken in with someone else's bigger foot. 9.5 foot here. I also wear size 10 shoes. 7.5D in a CCM. 8D in the Mako gives me about 1/4th of an inch to the toe after baking. The skates were difficult to get my foot into before baking. Share this post Link to post Share on other sites
DigiV 6 Report post Posted April 10, 2013 (edited) 9.5 foot here. I also wear size 10 shoes. 7.5D in a CCM. 8D in the Mako gives me about 1/4th of an inch to the toe after baking. The skates were difficult to get my foot into before baking.So you feel they are the perfect size for you? What about your instep? i get slight lace bite with the x60's. Edited April 10, 2013 by DigiV Share this post Link to post Share on other sites
jazzyjoey 2 Report post Posted April 10, 2013 (edited) Perfect size for sure. No lace bite at all. I originally felt some light pressure on my arches, but that went away after baking. Edited April 10, 2013 by jazzyjoey Share this post Link to post Share on other sites
Chadd 916 Report post Posted April 11, 2013 9.5 foot here. I also wear size 10 shoes. 7.5D in a CCM. 8D in the Mako gives me about 1/4th of an inch to the toe after baking. The skates were difficult to get my foot into before baking.1/4" is at least a half size and more likely a full size. Perfect size for sure. No lace bite at all. I originally felt some light pressure on my arches, but that went away after baking.It doesn't sound perfect. Share this post Link to post Share on other sites
DigiV 6 Report post Posted April 11, 2013 1/4" is at least a half size and more likely a full size. It doesn't sound perfect.hmm.. for me there's no way i'm getting into a 7.5D. I tried on a 8D pair of supremes (without baking) and felt they were a tad too small compared to my broken in X60's at 8.5D. So, if they really do mold into your foot and create length then 8's would be perfect. Your thoughts? Share this post Link to post Share on other sites
smcgreg 81 Report post Posted April 11, 2013 Thanks, I was leaning that way.Trukweaz?... Holy crap, is that you Kurt? Small world.Regarding the fit, I started in a 7 and the toes brushed, then went to a 6.5 and the toes were pretty jammed. After baking though, the 6.5s fit perfect. I have an E foot in supremes and the D width in the Mako is good. See you over on ST some time. Steve Share this post Link to post Share on other sites
Chadd 916 Report post Posted April 11, 2013 hmm.. for me there's no way i'm getting into a 7.5D. I tried on a 8D pair of supremes (without baking) and felt they were a tad too small compared to my broken in X60's at 8.5D. So, if they really do mold into your foot and create length then 8's would be perfect. Your thoughts? Go with what fits your foot, I was simply comparing his comments on them being perfect yet a 1/4" too big. Share this post Link to post Share on other sites
trukweaz 3 Report post Posted April 11, 2013 Trukweaz?... Holy crap, is that you Kurt? Small world.Regarding the fit, I started in a 7 and the toes brushed, then went to a 6.5 and the toes were pretty jammed. After baking though, the 6.5s fit perfect. I have an E foot in supremes and the D width in the Mako is good. See you over on ST some time. SteveThat's me! How's it?!Yea I might go try on the 7 again. In almost every skate I have owned a 41 (thats what the 7.5 is) is perfect. I dont mind a tiny space in front of the toe. as long as the volume and heal are good.best. Share this post Link to post Share on other sites
jazzyjoey 2 Report post Posted April 11, 2013 (edited) 1/4" is at least a half size and more likely a full size. It doesn't sound perfect.It's possible that it's less than 1/4'' then, I didn't really measure it with any accuracy. My foot started right against the toe of the skate pre-baking. After baking, there was a little bit of room. I might have overstated perfect, but they didn't have 7 3/4 size available :) Edited April 11, 2013 by jazzyjoey Share this post Link to post Share on other sites
shooter27 122 Report post Posted April 12, 2013 I'm really conflicted about sizing of this skate. I wear a 9 Bauer TotalOne but a 9.5 Graf. I've tried on both the 9 and 9.5 Mako and I'm conflicted. The 9 fits in the sense that my toes are against the end cap, but its not uncomfortable (obviously will open up with baking) but the 9.5 I still can feather the end of the cap. The upper of the 9.5 seems to fit me better than the 9. I'm very worried about how the 9.5 might open up too much with baking. Share this post Link to post Share on other sites